About the Book
This guide provides the information you will need in order to plan and install a TM5 / TM7 System.
This guide contains:
oan overview and description of the TM5 / TM7 System,
oinformation and requirements to plan your installation,
oinstallation procedure for your TM5 / TM7 System,
oinformation for commissioning and diagnosing your installation.
This document has been updated for the release of EcoStruxureTM Machine Expert V1.2.5.
The technical characteristics of the devices described in the present document also appear online. To access the information online, go to the Schneider Electric home page https://www.se.com/ww/en/download/.
The characteristics that are described in the present document should be the same as those characteristics that appear online. In line with our policy of constant improvement, we may revise content over time to improve clarity and accuracy. If you see a difference between the document and online information, use the online information as your reference.
|
Title of Documentation |
Reference Number |
|---|---|
|
Modicon M258 Logic Controller Hardware Guide |
|
|
Modicon LMC058 Motion Controller Hardware Guide |
|
|
Modicon TM5 Compact I/O Modules Hardware Guide |
|
|
Modicon TM5 Digital I/O Modules Hardware Guide |
|
|
Modicon TM5 Analog I/O Modules Hardware Guide |
|
|
Modicon TM5 Communication Modules Hardware Guide |
|
|
Modicon TM5 Expert (High Speed Counter) Modules Hardware Guide |
|
|
Modicon TM5 Transmitter and Receiver Modules Hardware Guide |
|
|
Modicon TM5 PCI Modules Hardware Guide |
|
|
Modicon TM5 Fieldbus Interface - Hardware Guide |
|
|
Modicon TM5 CANopen Interface Hardware Guide |
|
|
Modicon TM7 Digital I/O Blocks Hardware Guide |
|
|
Modicon TM7 Analog I/O Blocks Hardware Guide |
|
|
Modicon TM7 CANopen Interface I/O Blocks Hardware Guide |
|
|
EcoStruxure Machine Expert Compatibility and Migration - User Guide |
You can download these technical publications and other technical information from our website at https://www.se.com/ww/en/download/ .
|
|
|
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH |
|
oDisconnect all power from all equipment including connected devices prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment. oAlways use a properly rated voltage sensing device to confirm the power is off where and when indicated. oReplace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit. oUse only the specified voltage when operating this equipment and any associated products. |
|
Failure to follow these instructions will result in death or serious injury. |
|
|
|
UNINTENDED EQUIPMENT OPERATION |
|
oOnly use software approved by Schneider Electric for use with this equipment. oUpdate your application program every time you change the physical hardware configuration. |
|
Failure to follow these instructions can result in death, serious injury, or equipment damage. |
The following information applies to the TM5 System:
|
|
|
POTENTIAL FOR EXPLOSION |
|
oOnly use this equipment in non-hazardous locations, or in locations that comply with Class I, Division 2, Groups A, B, C and D. oDo not substitute components which would impair compliance to Class I, Division 2. oDo not connect or disconnect equipment unless power has been removed or the location is known to be non-hazardous. oDo not use the USB port(s), if so equipped, unless the location is known to be non-hazardous. |
|
Failure to follow these instructions will result in death or serious injury. |
The following information applies to the TM7 System:
|
|
|
POTENTIAL FOR EXPLOSION |
|
oOnly use this equipment in non-hazardous locations or in locations that comply either with the Class I, Division 2, Groups A, B, C and D, or with the ATEX Group II, Zone 2 specifications for hazardous locations, depending on your local and/or national regulations. oDo not substitute components which would impair compliance to the hazardous location specifications of this equipment. oDo not connect or disconnect equipment unless power has been removed or the location is known to be non-hazardous. |
|
Failure to follow these instructions will result in death or serious injury. |
