|
Code |
Description |
Comment |
|---|---|---|
|
0xC70A0000 |
No diagnostic information |
For internal use only. Contact your local Schneider Electric representative. |
|
0xC70A0050 |
Parameterization level is activated |
See FG Power Supply Mode |
|
0xC70A0051 |
Operating level is activated |
See FG Power Supply Mode |
|
0xC70A0500 |
Supply module in voltage control mode (power supply STM in state operation mode) |
See FG Power Supply Mode |
|
0xC70A0501 |
Supply module in current control mode (power supply STM in state operation mode) |
See FG Power Supply Mode |
|
0xC70A0502 |
Supply module ready for operation (power supply STM in state DC bus charged) |
See FG Power Supply Mode |
|
0xC70A0503 |
Supply module DC bus charging (power supply STM in state DC bus charging) |
See FG Power Supply Mode |
|
0xC70A0504 |
Control section ready for operation, mains voltage not available (power supply STM in state mains off) |
See FG Power Supply Mode |
|
0xC70A0505 |
Supply module ready DC bus charging (power supply STM in state power off) |
See FG Power Supply Mode |
|
0xC70A0506 |
Supply module DC bus is charged, supply module in rectifier mode or rectifier voltage control mode (power supply STM in state operation mode) |
See FG Power Supply Mode |
|
0xC70A0520 |
Supply module DC bus discharging |
See FG Power Supply Mode |
|
Code |
Description |
Comment |
|---|---|---|
|
0xC70C0000 |
No diagnostic information |
For internal use only. Contact your local Schneider Electric representative. |
|
Code |
Description |
Comment |
|---|---|---|
|
0xC70E0000 |
No diagnostic information |
For internal use only. Contact your local Schneider Electric representative. |
|
0xC70E2026 |
Undervoltage in power section |
DC bus voltage is less than minimum value |
|
0xC70E2027 |
Excessive oscillation in DC bus |
Oscillation of DC bus voltage is higher than maximum value |
|
0xC70E2029 |
Alert, device temperature monitoring in error |
Temperature sensor in error |
|
0xC70E2050 |
Device overtemperature alert |
Actual temperature higher than alert threshold |
|
0xC70E2086 |
Supply module overload alert |
- |
|
0xC70E2810 |
Drive system not ready for operation |
- |
|
0xC70E2812 |
Overtemperature in mains connection module / soft start module |
- |
|
0xC70E2814 |
Undervoltage in mains |
Mains voltage is less than the value specified for the device |
|
0xC70E2816 |
Undervoltage in power section |
- |
|
0xC70E2818 |
Phase interruption |
One phase is lost |
|
0xC70E2819 |
Mains interruption |
Mains voltage or frequency is out of specification |
|
0xC70E2820 |
Braking resistor overload alert |
- |
|
0xC70E2829 |
Not ready for power-on |
- |
|
0xC70E8025 |
Overvoltage in power section |
- |
|
0xC70E8026 |
Undervoltage in power section |
- |
|
0xC70E8028 |
Overcurrent in power section |
- |
|
0xC70E8057 |
Device overload, current limit active |
Command value of current is higher than current limit |
|
Code |
Description |
Comment |
|---|---|---|
|
0xC70F0000 |
No diagnostic information |
For internal use only. Contact your local Schneider Electric representative. |
|
0xC70F2018 |
Device overtemperature shutdown |
- |
|
0xC70F2022 |
Device temperature monitor in error |
- |
|
0xC70F2026 |
Undervoltage in power section |
- |
|
0xC70F2027 |
Excessive oscillation in DC bus |
Oscillation of DC bus voltage is higher than maximum value |
|
0xC70F2814 |
Undervoltage in mains |
Mains voltage is less than the value specified for the device |
|
0xC70F2815 |
Overvoltage in mains |
Mains voltage is higher than the value specified for the device |
|
0xC70F2818 |
Phase interruption |
One phase is lost or insufficient voltage |
|
0xC70F2819 |
Mains interruption |
Mains voltage or frequency is out of specification |
|
0xC70F2820 |
Bleeder resistor overload |
The load of the bleeder resistor is higher than the specified value |
|
0xC70F2821 |
Error in control of bleeder resistor |
Control unit of the bleeder does not work correctly |
|
0xC70F2834 |
Contactor control error |
Error detected with the feedback signal or the control unit of the mains contactor |
|
0xC70F8025 |
Overvoltage in power section |
DC bus voltage is higher than the value specified for the device |
|
0xC70F8028 |
Overcurrent in power section |
Current in power section is higher than the value specified for the device |
|
0xC70F8033 |
Short circuit to ground section |
Power section detected a current to ground higher than the value specified for the device |
|
0xC70F8070 |
Control voltage error |
Control voltage out of specification |
|
0xC70F8071 |
Overvoltage of control voltage |
Control voltage out of specification |
|
0xC70F8813 |
Connection error mains choke |
- |
|
0xC70F8815 |
Overvoltage in mains |
- |
|
0xC70F8817 |
Overvoltage in power section |
- |
|
0xC70F8820 |
Breaking resistor overload |
The load of the bleeder resistor is higher than the specified value |
|
0xC70F8821 |
Transistor short circuit of braking resistor control |
- |
|
0xC70F8830 |
Power section error |
- |
|
0xC70F8833 |
Ground fault current |
- |
|
0xC70F8835 |
Inconsistency in power section configuration |
- |
|
0xC70F8836 |
DC bus balancing monitor |
- |
|
0xC70F8838 |
Overcurrent external braking resistor |
- |
|
0xC70F8860 |
Overcurrent in power section |
- |
|
0xC70F8899 |
Unrecoverable error in power section |
- |