IF_RobotMotion - SetRamp (Method)

Overview

Type:	Method
Available as of:	V1.0.0.0

This chapter provides information on:

Task
Description
Interface
Diagnostic Messages

Task

Setting the ramp.

Description

With the method SetRamp(...), the ramp (change of the acceleration/deceleration) with which the path motion of the robot has to be executed can be determined.

Detailed description of the motion parameter Ramp.

A modified value of the ramp is active for the motion commands sent after calling this method.

Interface

Input	Data type	Description
i_etComponent	ET_RobotComponent	Specifies from which part of the robot that the motion parameters are to be set. Valid values are: ET_RobotComponent.All ET_RobotComponent.Path ET_RobotComponent.OrientationAll ET_RobotComponent.OrientationX ET_RobotComponent.OrientationY ET_RobotComponent.OrientationZ ET_RobotComponent.AuxAxAll ET_RobotComponent.AuxAx1 ... AuxAx10 For further information, refer to ET_RobotComponent.
i_lrValue	LREAL	Specifies the ramp (change of the acceleration/deceleration) with which the path motion of the robot has to be executed. The specification of the ramp can be executed again. The specification of the ramp applies to the motion commands following thereafter (MoveL, MoveC, ...). Unit: [-] Value range: i_lrValue > 0.0 AND i_lrValue >= Emergency ramp set with the method IF_RobotConfiguration.SetEmergencyParameter

Input

Data type

Description

i_etComponent

ET_RobotComponent

Specifies from which part of the robot that the motion parameters are to be set.

Valid values are:

ET_RobotComponent.All
ET_RobotComponent.Path
ET_RobotComponent.OrientationAll
ET_RobotComponent.OrientationX
ET_RobotComponent.OrientationY
ET_RobotComponent.OrientationZ
ET_RobotComponent.AuxAxAll
ET_RobotComponent.AuxAx1 ... AuxAx10

For further information, refer to ET_RobotComponent.

i_lrValue

LREAL

Specifies the ramp (change of the acceleration/deceleration) with which the path motion of the robot has to be executed.

The specification of the ramp can be executed again.

The specification of the ramp applies to the motion commands following thereafter (MoveL, MoveC, ...).

Unit: [-]

Value range: i_lrValue > 0.0 AND i_lrValue >= Emergency ramp set with the method IF_RobotConfiguration.SetEmergencyParameter

Output	Data type	Description
q_etDiag	GD.ET_Diag	General library-independent statement on the diagnostic. A value not equal to GD.ET_Diag.Ok corresponds to a diagnostic message.
q_etDiagExt	ET_DiagExt	POU-specific output on the diagnostic. q_etDiag = ET_Diag.Ok -> Status message q_etDiag <> ET_Diag.Ok -> Diagnostic message
q_sMsg	STRING[80]	Event-triggered message that gives additional information on the diagnostic state.

Output

Data type

Description

q_etDiag

GD.ET_Diag

General library-independent statement on the diagnostic.

A value not equal to GD.ET_Diag.Ok corresponds to a diagnostic message.

q_etDiagExt

ET_DiagExt

POU-specific output on the diagnostic.

q_etDiag = ET_Diag.Ok -> Status message

q_etDiag <> ET_Diag.Ok -> Diagnostic message

q_sMsg

STRING[80]

Event-triggered message that gives additional information on the diagnostic state.

Diagnostic Messages

q_etDiag	q_etDiagExt	Enumeration value	Description
OK	Ok	0	Ok
ExecutionAborted	ExternalPositionSourceConfigured	205	The external position source is configured.
InputParameterInvalid	AuxiliaryAxisNotConfigured	127	The auxiliary axis is not configured.
InputParameterInvalid	ComponentInvalid	132	The component is invalid.
InputParameterInvalid	RampRange	20	The ramp is out of range.
InputParameterInvalid	OrientationNotAvailable	199	The orientation is not available.

AuxiliaryAxisNotConfigured

Enumeration name:	AuxiliaryAxisNotConfigured
Enumeration value:	127
Description:	The auxiliary axis is not configured.

Issue	Cause	Solution
Setting the motion parameters was not successful.	The value transferred at the input i_etComponent does not correspond to a configured auxiliary axis.	Ensure that the axis is configured before using an auxiliary axis.

ComponentInvalid

Enumeration name:	ComponentInvalid
Enumeration value:	132
Description:	The component is invalid.

Issue	Cause	Solution
Setting the motion parameter was not successful.	The value transferred at the input i_etComponent is invalid.	Ensure that at the input i_etComponent a valid component has been transferred.

ExternalPositionSourceConfigured

Enumeration name:	ExternalPositionSourceConfigured
Enumeration value:	205
Description:	The external position source is configured.

Issue	Cause	Solution
Setting the motion parameter was not successful.	An external position source for the robot components cartesian, orientation and auxiliary axes is configured.	Setting the motion parameter for the component Path is not possible when an external position source for the robot components is configured. Do not set the motion parameter for the component Path.

Issue

Cause

Solution

Setting the motion parameter was not successful.

An external position source for the robot components cartesian, orientation and auxiliary axes is configured.

Setting the motion parameter for the component Path is not possible when an external position source for the robot components is configured.

Do not set the motion parameter for the component Path.

Ok

Enumeration name:	Ok
Enumeration value:	0
Description:	Ok

The motion parameter has been set successfully.

OrientationNotAvailable

Enumeration name:	OrientationNotAvailable
Enumeration value:	199
Description:	The orientation is not available.

Issue	Cause	Solution
Setting the motion parameter was not successful.	The orientation transferred at the input i_etComponent is not available.	Ensure that the transformation used supports the orientation.

RampRange

Enumeration name:	RampRange
Enumeration value:	20
Description:	The ramp is out of range.

Issue	Cause	Solution
Setting the motion parameter was not successful.	The value transferred at the input i_lrValue lies outside the valid range.	At the input i_lrValue, a value greater than 0 must be transferred. At the input i_lrValue, a value less than emergency ramp must be transferred.

Issue

Cause

Solution

Setting the motion parameter was not successful.

The value transferred at the input i_lrValue lies outside the valid range.

At the input i_lrValue, a value greater than 0 must be transferred.

At the input i_lrValue, a value less than emergency ramp must be transferred.